Shop
Anycubic Wash & Cure 3 Plus
17,885.00 EGPAnycubic Wash and Cure 3 Plus
● Size Upgrade: 7.6L Curing Size 228*128*260mm
● Enhanced Curing: Increase Energy Value 30,000uW/cm² by Gooseneck Lights
● IPA Saving: Dual-layer Curing Platform
Anycubic Wash & Cure Max
37,275.00 EGP● 14.9L Impressive Maximum Cleaning Size
● Spray Cleaning and 360° Dimensional Curing
● Alcohol-Efficient, Saving over 50%
Anycubic Wash & Cure 3
12,795.00 EGP●4L Extra-Large Cleaning Bucket Size
● Gooseneck Light: Localized Strengthening,Uniform Curing
● Dual-layer Design, IPA Saving
Arduino UNO
Original price was: 400.00 EGP.340.00 EGPCurrent price is: 340.00 EGP.The Arduino Uno R3 is a open source microcontroller board based on the ATmega328 chip. This Board has 14 digital input/output pins, 6 analog input pins
Arduino Uno R3 with Cable
Original price was: 600.00 EGP.450.00 EGPCurrent price is: 450.00 EGP.3d printer accessories
ARDUINO UNO REV3 -A000066 ORIGINAL
Original price was: 1,500.00 EGP.1,250.00 EGPCurrent price is: 1,250.00 EGP.ARDUINO UNO REV3 -A000066
Assembled Extruder Kit for ELEGOO Neptune 4/4 Pro (Full Head)
6,000.00 EGPCompatibility
Neptune 4
Neptune 4 PRO
Auto Leveling Sensor Module for E3D V6
135.00 EGPEnhance 3D printing with E3D V6 Auto Leveling Sensor. Easy setup, universal fit, ±0.05mm precision, 500,000+ cycles, strong anti-interference performance
Bambu Lab A1 3D Printer
84,985.00 EGPBambu Lab A1 3D Printer
- Full-auto Calibration
- Multi-Color Printing (Combo Version)
- Active Flow Rate Compensation
- 1-Clip Quick Swap Nozzle
- Active Motor Noise Cancelling
- 256*256*256 mm³ Build Volume
Bambu Lab A1 mini
59,995.00 EGPProduct Features
- Full-auto Calibration.
- 4-Color Printing with AMS lite.
- Under 48 dB Low Noise in Silent Mode.
- Full-metal Linear Rails and Bearings.
- Vibration and Flow Rate Compensation.
Bambu Lab A1 mini AMS included ( EU Version )
74,995.00 EGPProduct Features
- Full-auto Calibration.
- 4-Color Printing with AMS lite.
- Under 48 dB Low Noise in Silent Mode.
- Full-metal Linear Rails and Bearings.
- Vibration and Flow Rate Compensation.
Bambu Lab A1 with AMS included ( EU Version )
99,995.00 EGPProduct Features
- Full-auto Calibration
- Multi-Color Printing (Combo Version)
- Active Flow Rate Compensation
- 1-Clip Quick Swap Nozzle
- Active Motor Noise Cancelling
- 256*256*256 mm³ Build Volume
- The upgraded heatbed cable features Kevlar reinforcement, thicker insulation, softer copper, optimized wire winding interval, Nylon sleeving and a extended strain relief.
Bambu Lab AMS lite for A1 series
15,000.00 EGPBambu Lab AMS lite for A1 series
- Multi-Color/Multi-Material Capability
- Automatic Filament Backup
- Improved Spool Compatibility
- Easy to Maintain
- RFID Filament Sync
Bambu Lab X1 Carbon Hot end
3,900.00 EGPBambu Lab X1 Carbon CHT Hot end
Upgraded 3D Extrusion Head for Bambu Lab X1 Printer Hot End High Temperature Wear Hardened Steel Nozzle Thermistor Hotend Kit
Bed Leveling Hand Adjustment Fixing Kit M3 Screw
60.00 EGPUM2 Bed Leveling Hand Adjustment Fixing Kit M3 Screw (4pcs)
BIGTREETECH TMC2130-V3.0
400.00 EGPTmc 2130 is ahigh-performance two–phase stepper motor driver chip with standard spi interface and a simple step/dir interface very low noise , high load driver does not lose step
Bimetal Titanium Alloy Copper Throat pipe for (Ender-3 V2 neo, Ender-3 max neo, CR-10 smart, CR-6 SE, CR-6 Max)
220.00 EGPMaterial of Bi-metal heatbreak: Red brass/copper and Titanium alloy
BIQU 3D Scanner Controller board
300.00 EGPStepper motor driver DRV8825 with Micro-stepping capability. The module has a pinout that is identical to A4988 driver, yet it affoards better performance. Both drivers are compatible with the RAMPS shield for 3D printers and CNC.
BL touch (3D Touch Sensor)
Original price was: 800.00 EGP.750.00 EGPCurrent price is: 750.00 EGP.The main functions and controls of BLTouch are the same as the usual auto bed leveling sensor, consisting of RC servo and microswitch.
BL touch 3D Touch Sensor 1meter
BL touch (3D Touch Sensor) 1.5m
850.00 EGPThe main functions and controls of Blouch are the same as the usual auto bed leveling sensor, consisting of RC servo and microswitch.
BL touch 3D Touch Sensor 1.5 meters
Black Plastic Injection Molding filament Holder
70.00 EGPBlack Plastic Injection Molding Holder Size of the holder is about 16.6 x 2.4 x3.3 cm /6.53×0.94×1.30 inch , is now available at lancer3d
Black Silicon leveling Spacer
15.00 EGPSilicone Solid Spacer Hot Bed Leveling Silica Column 18mm Compatible For Ender-3/Ender-5/CR-X/CR-10 3D Printer Parts
BlueCast X-One V2 for mono LCD/DLP 500g
15,000.00 EGPX-One® V2 is the real meltable resin developed and produced by BlueCast® for DLP and Monochromatic LCD machines. Thanks to the low-temperature melting polymer it ensures a smooth surface finish and perfect lettering.
Brass Nozzle for K1/ K1 Max
80.00 EGP
Brass Nozzle For Anycubic Kobra 3 (1.75mm)
60.00 EGP
Brass Nozzle for Ender 3 V2 neo – Max neo – CR-10 SMART
55.00 EGP
Brushless DC Fan 12V
40.00 EGP – 45.00 EGPBrushless DC Fan 12V
Camera for Elegoo Orangestorm Giga
3,000.00 EGPCamera for Elegoo Orangestorm Giga – Real-Time Print Monitor
Cartridge Heater 12V/24V 40W (1m) 6*20
40.00 EGP – 45.00 EGP6*20 Cartridge Heater 12V/24V (1m) Power: 40W head size: 6*20mm Heating head material: 304 stainless steel Heating temperature: up to 350
Cartridge Heater 12V/24V 50W (1m) 6×20
45.00 EGP – 50.00 EGP6*20 Cartridge Heater 12V/24V (1m) Power: 50W head size: 6*20mm Heating head material: 304 stainless steel Heating temperature: up to 350
Chrome zirconium copper Nozzle for Ender 3 V2 neo – Max neo – CR-10 smart
100.00 EGP
CHT High Flow Hard Steel Nozzle for Bambu Lab x1 P1P 1.75mm
120.00 EGP
Cr10 Hotend
450.00 EGP – 580.00 EGPThe new radiator size fits most 3D printers, improving nozzle heat conduction with a copper block. Compatible with 3mm OD NTC, like PT1000 thermal resistance. Max working temp: 500°C
CR10 Hotend Block High quality
100.00 EGPCR10 hotend block ,High Quality CR10 Heater Block MK8 Silicone Sock CR10 Hotend Extruder For Creality Ender 3 MK7/MK8/MK9 Block